My logic equal group IP is 192.168.0.1 and my two other members of storage are 192.168.0.2 and 192.168.0.3 no port management "management of ports are not configured and is unable to be present due to the direction and iscsi are on the same subnet. You can also open a pension case and Dell will help you at this yard.ĮqualLogic PS6000 Serires IP address changing For quite a time, try to is not on the table. The two appear? If this isn't the case, then I guess you might be running and older version of the firmware. If you use a good drive from Dell, you have another piece of spare not appearing in this member? If so, swap the new drive with the spare and put the spare wheel in the open slot. Are there messages in EQL GUI Event Viewer when you insert the new drive? Leaving the reader in until replacement is to properly maintain the airflow for cooling.Īt you will replace it by a car brand from EQL, Dell? Discs no Dell won't work. I suspect you have the cause of the problem. I exctracted the disc more than 1 hour so that the system put the large/empty slot and now no discs are recognized. I have a new drive, but I can't add it to the system because I made a stupid mistake. Try to ping the new IP addresses of existing hosts and if everything is OK, move member in your production area.Ī few days ago, I found a disk fail on my PS4100. Updated the FW and also check the FW drive. I prefer a complete reconstruction and not a fast initialization, but it's your choice. If the table has joined this pool complete the configuration as Ports IP/network, RAID level and so on. Let the new Member to join an EMPTY pool as the "default" (its still a void in our environments) or create an and name the program installation or maintenance. How can I upgrade the firmware on the new PS4100 before running the Setup utility? We have a new PS4100 which was delivered with the 7.0.15 Firmware but the Group has a range of PS4000 on Firmware 8.0.5. Data in a pool are distributed to members in the same pool.Īnyone would be able to explain the process of adding a new table to an existing group, please? RAID levels do not in the Member States in a pool. It is this level that offers the advantage of this combination. The only available RAID option is "accelerated RAID6. A small set of disks SSD and balance SAS drives. Yes, sorry, it was supposed to be 'impossible '.Ī 'Hybrid' 6000 model cannot SSD + SAS drives in the SAME chassis. The group does not appear when you run as expected and the e/s is higher on rotating disks on the SSD (seems backwards).Ĭan someone confirm this for me? I'm not find documents confirming the he.Īny help would be greatly appreciated, perhaps there is a configuration setting that you miss? There may be a configuration there guide I'm not find? With the new firmware (V7.1.2) we understand that the creation of a group, and identify as such SSD table, it was supposed to perform in the form of a table of the hybrid. EQL no readers will be spotted and unused. What kind of discs that we could use, because we think this drives needs a special Branded Firmware. The disk used current (Seagate ST31000340NS) are EOL To reduce the risk, we want to replace it. One of the disks in our Dell PS6000 told us that it is a failure. I was running just the substitution as the wrong user command I tried the switch of replacement ssh command and it fails with "- override - downgrade: not found".Ĭurrently waiting for my account techdirect to be configured, but it seems to take forever I'm trying to downgrade the firmware on a version 9.0.2 to 8.1.4 PS4100 so that I can use the 1.2 with VMware vshere 5.1 MPIO drivers. You also need user and password.ĮqualLogic firmware downgrade 9.0.2 to 8.1.4 PS4100 help! If you hands away you can connect a serial cable to the module active controller with parameters 9600,8,1, n in your terminal program favorite (we often use PuTTY). If you do not have a password try "grpadmin. If you do not get a response that is active and sound using a different subnet in regards to the Storage (iSCSI). You need java installed to get the GroupManager that run in the browser. So check your host what address he used for iSCSI to table connection and try a browser with or a ssh client and see what happened. The management is optional and it may not be configured. I have someone on site who can provide remote hands.Ĭan I connect a laptop and get or does dell provides support paid for it? We have a very old EqualLogic PS4100 with a red light a remote site (connected to a production server and works very well)Īdmin has already left, and we do not have its IP management or identifying information.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |